حرك مؤشر الماوس فوق الصورة للتكبير

الماركة:

SUNSKY

SUNSKY SINOTIMER SDM009 Din Rail Single-Phase Voltage Current Frequency Power Factor Electricity Multifunctional Meter AC40-300V Built-In

د.إ 52.1120% خصم
د.إ41.57
لكل قطعةشامل ضريبة القيمة المضافة
1 قطعة
د.إ 52.1123% خصم
د.إ40.33
لكل قطعةشامل ضريبة القيمة المضافة
2 - 9 قطعة
د.إ 52.1125% خصم
د.إ39.08
لكل قطعةشامل ضريبة القيمة المضافة
10+ قطعة
نقبل
الدفع عند الاستلام
التحويل المصرفي
حد ائتمان

معلومات عن هذا المنتج

Measurement accuracy: 1+/-2 percent of the word

Measuring range:

- Voltage: AC40-300V (for 110V 220V)/AC250-450V (for 380V 450V)

- Current: 0.00-100.0A universal

- Active power: 0-60000W/0-45000W

كمية (قطعة)

الحد الأدنى لكمية الطلب هو 1 قطعة

الحد الأدنى للطلب:1 قطعة

الشحن والإرجاع


طلبات الإرجاع
سياسة الإرجاع الخاصة بالبائع اعرف المزيد

سيتم عرض السعر النهائي وتواريخ التوصيل وخيارات الشحن الإضافية عند إتمام عملية الشراء والدفع.

معلومات عن البائع

معتمد

الصين

المزيد من هذا البائع

نظرة عامة

معرف وحدة إدارة المخزون للبائع:
TBD0604630001
ورقة المواصفات الفنية متوفرة حسب الطلب
لا
Dangerous goods
No
Item length
9
Item width
6
Item height
7
Item weight
0.16
Item weight unit
kg
Item dimensions unit
cm

وصف المنتج


1. Measurement accuracy: 1+/-2 percent of the word
2. Measuring range:
- Voltage: AC40-300V (for 110V 220V)/AC250-450V (for 380V 450V)
- Current: 0.00-100.0A universal
- Active power: 0-60000W/0-45000W
- Frequency: 45-65Hz
- Electricity (power): 0-9999Kwh
- Power factor: 0.00-4.00PF
3. Measuring speed: 2 times/s
4. Installation mode: rail type
5. Overall dimensions: 54 x 80 x 64mm
6. Protruding size: 45 x 16mm

Usage and wiring method:
1. Connect the measured voltage to terminals 1 and 2 on the lower left side of the meter
2. Built-in transformer according to figure 1 wiring diagram wiring, the measurement circuit of the wire through the instrument lower hole, the wire into the direction of the user according to the use of arbitrary choice, can be from the instrument lower hole into the upper out, or from the instrument upper holes into the lower out, into the direction of the different will not affect the results of the measurements
3. Connect the external transformer according to the wiring diagram in figure 2, connect the two wires of the secondary end of the precision current transformer with the instrument to the 3 and 4 terminals on the upper left side of the instrument, and pass the wires of the measuring circuit through the hole of the transformer
4. When the power is turned on, the meter displays the measurement parameters
5. When it is necessary to reset the power measurement (when the measurement starts from zero), press and hold the button on the right side of the meter panel (RESET) for 5 seconds (press and hold and stay for 5 seconds) until the power is displayed as 0, then release the button, then the power measurement starts from zero
6. Power outage automatic data saving function, that is, when the measurement voltage is disconnected or power failure, the meter will automatically save the current test data, when reconnected to the measurement of the power supply meter will continu